User Manual
Smart Recessed Lighting Kit
Intended for:FSPC999W-F1
Thank you for purchasing Smart Recessed Lighting Kit. This kit adopts the standard Zigbee3.0 communication protocol, compatible with multi-platform use, easy to install, simple to use, and can provide stable and simple wireless control for lighting. With dimming, color adjustment, and other functions, to meet the daily lighting, but also to create a sense of leisure, comfort, and other atmospheres, to meet the needs of your rich personality lighting scene.
Power supply voltage: 100-120Vac
Rated power: 13W
Power number:0.9
Color temperature: 2700K-6500K+RGB
Color mixing mode: RGBW color mixing
Color rendering index:>90
Lumen:1100LM
Operating frequency: 60Hz
Operating Temperature Range: -25℃~+70
Network protocol standard: ZigBee 3.0
Size:85mm(R)*22.5mm(H)
1.Install the Recessed Lights (refer to Chapter 3 for details).
2.Connect the Matter gateway (refer to Chapter 4, also refer to the gateway operation instructions).
3.Connect the platform to use (refer to Chapter 5 for details).
Toggle
the Light powered on and off 5 times within 10s (pay attention to the power off
and on interval 1S), the light blinked three times, and the device reset
successfully, at this time the device is in the state of looking for the
network for the 60S.
Long
press the RESET button at the bottom of the gateway for 5S, the white light of
the indicator light flashes, restoring factory settings is successful and the
gateway starts
On your
IOS mobile device, open the "Home" app and sign in with your Apple
ID.
"Home” APP → Upper Right”
+" → "Add or Scan
Accessories" → Mobile phone close to HomePod, you can scan the device, according to the APP
prompts to add the configuration Add the Matter gateway after the Homepod configuration is complete!
Important Reminder: Before proceeding with the operation, please ensure that the gateway has been powered on for less than 10 minutes. If it has been powered on for more than 10 minutes, you need to power off the gateway and then power it on again.
Open the "Home" APP of IOS mobile phone → Upper Right”+" → "Add or Scan Accessories" → Scan the QR code of Matter at the back of the gateway to add it, and add the Matter gateway according to the APP prompts. Add Matter gateway, after adding, you can see the successfully added gateway in "Home Settings" → "Home Hubs & Bridge".
View
Matter Gateway
Steps: Open IOS mobile phone "Home" APP → 1 Upper Right "..." → 2 “Home Settings” → 3 “Home Hub & Bridges” → 4 Select the bridged Matter gateway → 5 Turn on pairing mode (triggering gateway allow matching), at this time the Matter gateway began to allow access to the network 120S, the gateway indicator light color gradient, while the trigger light into the network to find the pairing mode (continuous power on/off 5 times), at this time the device will enter the automatic pairing, such as lights to add a successful will be displayed in the device list, at this time you can control the lights, if the device is not found within 120S, reopen to add the steps.
Note: The gateway and the Echo device need to be on the same LAN and the network-enabled for IPV6
Search and download the "Amazon Alexa" app in the app market, install and register according to the prompts, and open "Alexa" APP → Devices → Upper Right” +" → Add Device →Amazon Echo → According to the APP operating instructions to configure the network, the configuration is complete you can see the Echo speaker in the Devices list.
Important Reminder: Before proceeding with the operation, please ensure that the gateway has been powered on for less than 10 minutes. If it has been powered on for more than 10 minutes, you need to power off the gateway and then power it on again.
Open "Alexa" APP → Devices → Upper Right”+” → Add Device → Other → Matter → Scan the QR code of Matter on the back of the gateway according to the
APP operation guide. If it fails, restore the factory settings of the gateway
and add it again.
Open the “Alexa”APP → Devices →All Device→ Select the corresponding Bridged Gateway →Open Enaled →Other Assistants and Apps→Add another(triggering gateway allow matching), at this time the Matter gateway began to allow access to the network 120S, the gateway indicator light color gradient, while the trigger light into the network to find the pairing mode (continuous power on/off 5 times), at this time the device will enter the automatic pairing, such as lights to add a successful will be displayed in the device list, at this time you can control the lights, if the device is not found within 120S, reopen to add the steps.
Note: The gateway and Google Home
speaker device need to be in the same LAN and the network is enabled for IPV6
Open Google "Home" APP → Devices → Add device → according to the APP operation guidelines to configure the network, the configuration is complete and can be viewed in the Devices speaker
Important Reminder: Before proceeding with the operation, please ensure that the gateway has been powered on for less than 10 minutes. If it has been powered on for more than 10 minutes, you need to power off the gateway and then power it on again.
Open Google "Home" APP → Devices → Add →New device → Select the corresponding room → Looking for devices →Set up this device → Scan Matter QR code → According to APP prompts. Scan
the QR code of Matter behind the gateway to add, you can see the successfully
added Matter Gateway in the device list if you add successfully, if you fail to
add, the Matter Gateway will be restored to the factory settings and re-added.
Trigger the gateway to allow pairing: Open Google "Home" APP → Devices → Select the corresponding Bridged Gateway → Linked Matter apps & services → Linked apps & services, at this time, the color of the gateway indicator light will fade, and it will enter the allow pairing mode (at this time, the trigger light will enter the find network pairing mode). At this time, the gateway indicator light color gradient, into the allowed pairing 120S, and at this time the trigger light into the network to find the pairing mode (10S within the continuous power off and on 5 times), at this time the device will enter the automatic network to find the pairing mode, such as the device pairing will be successful in the list of devices will be displayed, that you can control the device, such as adding failure, re-operate to add steps.
For more
information on how to use the platform, please download the e-Manual, download
link: http://xskylight.com/doc/FSPC999W_manual.html
1、This product is wireless
communication, please do not place the product in a metal box to work, in case
the signal is shielded;
2, the
surrounding environment temperature range: -25 ℃ ~ +70 ℃, ambient humidity:
maximum 95% RH;
3、Avoid using in chemical or combustible
gas, saturated salt spray, highly humid for a long time, or another abnormal
environment;
4、It should be installed in a place
where there is no rain or snow intrusion, and the medium is free of gas and
dust sufficient to corrode the metal and destroy the insulation, not to mention
the danger of explosion.
The
company's products are free of charge warranty for one year (except for the
appearance of parts and personal damage caused by improper use);
The
following cases are not covered by the free warranty:
1.
Machines that have been disassembled or repaired by non-authorized maintenance
centers;
2、Damage caused by natural disasters
such as flood, fire, lightning, and so on;
3, due
to falling, extrusion, immersion, moisture, and other human-caused damage;
4,
product failure caused by not using the product by the rated parameters
(voltage, etc.) of the product instruction manual (the shell is not covered by
the warranty).